955 Canal Road Extd., Manchester, PA 17345, US

Welcome to Artistry In Titanium

Titanium Tools

Titanium T-Grip Driver Set

The Titanium T-Grip Driver set is the third design in the series. 


It features a 1/4” square drive socket that is permanently secured into the body. The body, T-bar, and spinner of the main driver are all machined from solid titanium. 


The body and spinner both have a pattern of slots and grooves (similar to that on my Twister Pens) to provide a secure, yet comfortable grip.


Each set comes complete with the main driver, T-bar, spare O-Rings for the T-bar, a #1 Phillips bit, a #2 straight blade bit, and a magnetic thumb driver that converts the 1/4” square drive into a magnetic 1/4” hex drive. All of the components are high quality and made in the U.S.


T-Grip Driver Set Specifications:

Body: Made from solid ø5/8" 6AL4V titanium bar stock.

T-Bar: Made from solid ø1/4” 6AL4V titanium bar stock.

Spinner: Made from solid ø1 1/4" 6AL4V titanium bar stock.

Spinner screw: 8-32" stainless steel button head

Overall length: approximately 5 1/4" (without accessories installed)

Weight: approximately 5.3 ounces

The driver bits are high quality tool steel from Apex ®.


Price: $395.00 shipped in the continental US. Sorry, no foreign orders can be accepted.

Magnetic Driver Set

For those who appreciate fine tools, this Titanium Magnetic Driver set is the second in the series. 


It features a 1/4” hex magnetic drive socket that is permanently secured into the body. The body, and spinner of the main driver are both machined from solid titanium. 


The body and spinner both have a pattern of slots and grooves (similar to that on my Twister Pens) to provide a secure, yet comfortable grip.


Each set comes complete with #5, #6, #7, and #8 Torx® bits in 2" lengths, a 2 3/4” long #8 Torx® bit, a #2 straight blade bit, a #1 Phillips bit (6 bits total). All of the components are high quality Apex® bits - made in the U.S.


Magnetic Driver Set Specifications:

Body: Made from solid ø5/8" 6AL4V titanium bar stock.

Spinner: Made from solid ø1" 6AL4V titanium bar stock.

Spinner screw: #8-32 stainless steel button head

Overall length: approximately 5 1/8" (without bit installed)

Weight: approximately 4.6 ounces


The driver bits are high quality tool steel from Apex ®. NOTE: The bits are secured both with a steel snap ring and magnet for extra security. Therefore, pliers might be required for toolbit changes.


Price: $375.00  shippied in the continental US. Sorry, no foreign orders can be accepted.


These tool sets are made in limited numbers. Please email me to verify availability:


Email Tom

Titanium Fid

This new Titanium Fid was developed in response to requests from several people who work with paracord and leather. The design is based on a simple tool, but features several enhancements for strength, accuracy, and comfort. It's already been called "a cord worker's dream" and is much better than using a common nail set or knitting needle for this type of precision work.


Machined from one solid piece of ø13mm 6AL4V titanium (slightly over ø1/2"), the integral shaft is turned to an approximate ø3/16", then tapered and finished with a fine, smooth point. The grip area features my trademark "grenade" machining pattern (the same as used on my Twister pens) for positive, yet comfortable control. 


Each titanium fid is supplied in a standard satin polished finish. There's even a hole near the end of the grip so you can attach a lanyard or wear it on a chain around your neck.


The overall  length is approximately 4 1/2" and each one weighs about 1.3 ounces. And, because it's machined from one solid piece of 6AL4V titanium, it should last a lifetime. 


Price: $170.00 each shipped in the Continental US. Please email me if you'd like to place an order. Sorry, no foreign orders can be accepted.


 

 

Ordering link:

Please contact me via the following link to purchase any of these tools:



Email Tom